Print Page Email Page Smaller Text Larger Text

ISO - Engineering Components & Equipment Collection

This collection contains documents from the following standards organization(s): International Organization for Standardization

Most Popular Standards from the ISO - Engineering Components & Equipment Collection

ISO 11469 EN-Plastics - Generic Identification and Marking of Plastic Products-Second Edition 
ISO 3269 EN-Fasteners - Acceptance Inspection-Third Edition 
ISO 228-1 EN-Pipe Threads Where Pressure-Tight Joints Are Not Made on the Threads - Part 1: Dimensions Tolerances and Designation-Fourth Edition 
ISO 281 EN-Rolling bearings - Dynamic load ratings and rating life-Second Edition 
ISO 1133 EN-Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics-Fourth edition 
ISO 1043-1 EN-Plastics - Symbols and Abbreviated Terms - Part 1: Basic Polymers and Their Special Characteristics-Third Edition 
ISO 22196 EN-Plastics - Measurement of antibacterial activity on plastics surfaces-First Edition 
ISO 3800 EN-Threaded Fasteners - Axial Load Fatigue Testing - Test Methods and Evaluation of Results First Edition; 
ISO 23671 EN-Passenger car tyres Method for measuring relative wet grip performance Loaded new tyres-First Edition 
ISO 898-7 EN-Mechanical Properties of Fasteners - Part 7: Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1 mm to 10 mm-First Edition 
ISO 10664 EN-Hexalobular internal driving feature for bolts and screws-Second Edition 
ISO 178 EN-Plastics - Determination of Flexural Properties-Fourth Edition; Amendment 1: 02/15/2004 
ISO 3386-1 EN-Polymeric Materials Cellular Flexible - Determination of Stress-Strain Characteristic in Compression - Part 1: Low-Density Materials Second Edition 
ISO 11359-2 EN-Plastics - Thermomechanical Analysis (TMA) - Part 2: Determination of Coefficient of Linear Thermal Expansion and Glass Transition Temperature-First Edition 
ISO 11359-1 EN-Plastics - Thermomechanical Analysis (TMA) - Part 1: General Principles-First Edition 
ISO 7214 EN-Cellular Plastics - Polyethylene - Methods of Test-Third Edition 
ISO 8528-1 EN-Reciprocating internal combustion engine driven alternating current generating sets Part 1: Application ratings and performance-Second Edition 
ISO 1328-1 EN-Cylindrical Gears - ISO System of Accuracy - Part 1: Definitions and Allowable Values of Deviations Relevant to Corresponding Flanks of Gear Teeth-First Edition; Corrected and Reprinted - 02/01/1997 
ISO 9982 EN-Belt Drives - Pulleys and V-Ribbed Belts for Industrial Applications - Dimensions - PH PJ PK PL and PM Profiles: Dimensions-Second Edition 
ISO 10816-6 EN-Mechanical Vibration - Evaluation of Machine Vibration by Measurements on Non-Rotating Parts - Part 6: Reciprocating Machines with Power Ratings Above 100 kW First Edition 
ISO 6336-5 EN-Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials-Second Edition 
ISO 7-2 EN-Pipe Threads Where Pressure-Tight Joints Are Made on the Threads - Part 2: Verification by Means of Limit Gauges-Second Edition 
ISO 7089 EN-Plain Washers - Normal Series - Product Grade A-Second Edition 
ISO 868 EN-Plastics and Ebonite - Determination of Indentation Hardness by Means of a Durometer (Shore Hardness)-Third Edition 
ISO 6603-1 EN-Plastics - Determination of Puncture Impact Behaviour of Rigid Plastics - Part 1: Non-Instrumented Impact Testing-Second Edition 
ISO 965-1 EN-ISO General Purpose Metric Screw Threads - Tolerances - Part 1: Principles and Basic Data-Third Edition 
ISO 10300-2 EN-Calculation of Load Capacity of Bevel Gears - Part 2: Calculation of Surface Durability-Corrected Version; 5/15/2003 
ISO 527-2 EN-Plastics - Determination of Tensile Properties - Part 2: Test Conditions for Moulding and Extrusion Plastics-First Edition 
ISO 4762 EN-Hexagon socket head cap screws-Fourth Edition 
ISO 8528-9 EN-Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets - Part 9: Measurement and Evaluation of Mechanical Vibrations First Edition 
ISO 898-2 EN-Mechanical Properties of Fasteners - Part 2: Nuts with Specified Proof Load Values - Coarse Thread-Second Edition 
ISO 8528-5 EN-Reciprocating internal combustion engine driven alternating current generating sets - Part 5: Generating sets-Second Edition 
ISO 2341 EN-Clevis Pins with Head-Second Edition 
ISO 273 EN-Fasteners - Clearance Holes for Bolts and Screws-First Edition; Amendment Slip-1979; NZS/ISO 273: 1979 
ISO 1043-2 EN-Plastics - Symbols and Abbreviated Terms - Part 2: Fillers and Reinforcing Materials-Second Edition 
ISO 10642 EN-Hexagon socket countersunk head screws-Second Edition 
ISO 4156-1 EN-Straight cylindrical involute splines - Metric module side fit - Part 1: Generalities-First Edition; Together with ISO 4156-2 and ISO 4156-3 Replaces ISO 4156 
ISO 4892-1 EN-Plastics - Methods of Exposure to Laboratory Light Sources - Part 1: General Guidance-Second Edition 
ISO 10964 EN-Adhesives - Determination of Torque Strength of Anaerobic Adhesives on Threaded Fasteners First Edition 
ISO 3601-3 EN-Fluid power systems - O-rings - Part 3: Quality acceptance criteria-Second Edition; Corrected and Reprinted 04/15/2006 
ISO 8528-3 EN-Reciprocating internal combustion engine driven alternating current generating sets - Part 3: Alternating current generators for generating sets-Second Edition 
ISO 492 EN-Rolling Bearings - Radial Bearings - Tolerances-Fourth Edition 
ISO 75-2 EN-Plastics - Determination of Temperature of Deflection under Load - Part 2: Plastics and Ebonite-Second Edition 
ISO 1502 EN-ISO General-Purpose Metric Screw Threads - Gauges and Gauging-Second Edition 
ISO 4753 EN-Fasteners - Ends of Parts with External ISO Metric Thread-Second Edition 
ISO 7045 EN-Pan Head Screws with Type H or Type Z Cross Recess - Product Grade A-Second Edition 
ISO 3167 EN-Plastics - Multipurpose Test Specimens-Fourth Edition 
ISO 6157-3 EN-Fasteners - Surface Discontinuities - Part 3: Bolts Screws and Studs for Special Requirements First Edition 
ISO 13586 EN-Plastics Determination of fracture toughness (GIC and KIC) Linear elastic fracture mechanics (LEFM) approach AMENDMENT 1: Guidelines for the testing of injection-moulded plastics containing discontinuous reinforcin 
ISO 3251 EN-Paints varnishes and plastics - Determination of non-volatile-matter content-Fourth Edition